Garage shelving for 27-gallon totes needs about 21 5/8 to 22 5/8 in. of usable depth if the totes sit long side out, and about 30 1/2 to 32 1/2 in. if they slide in end first. Those figures come from Sterilite’s listed sizes for its two 27-gallon Industrial Totes, 30 1/2 x 20 5/8 x 15 1/4 in. and 28 1/2 x 19 5/8 x 15 1/2 in., plus 1 in. of clearance front and back. Other brands’ 27-gallon totes have their own footprints, so measure yours before you buy shelving. For 18- to 38-gallon totes and mixed sizes, see how deep garage shelves should be for totes.
As an Amazon Associate I earn from qualifying purchases.
How we researched this: As of November 2026, we took tote dimensions from Sterilite’s product pages and worked out the clearances, widths and loads in this guide from them. It covers shelf types and fit criteria rather than ranking specific shelving models.
Why 27-gallon totes aren’t one size
“27 gallons” describes volume, not footprint. Sterilite alone sells two 27-gallon Industrial Totes: one is 30 1/2 x 20 5/8 in., the other 28 1/2 x 19 5/8 in. Two inches of length is the difference between two totes fitting side by side on a shelf and one hanging off the end.
Makers list exterior dimensions, and totes are widest at the rim, where the lid and handles sit. That rim measurement is the one that decides whether a tote fits between the posts.
How to measure your totes and shelf
- Measure the lidded tote at its widest points: length, width and height, including handles and latches.
- Pick an orientation. Long side out, the tote’s width runs into the shelf. End out, its length does.
- Measure the shelf opening, not the unit. Measure between the posts, from the back brace to the front edge, and from the deck to whatever sits above it. A unit sold as 72 in. wide has less than 72 in. between its posts.
- Measure the garage around it: wall width, the unit’s full depth, and the room you need to pull a tote straight out past the car and door tracks.
- Weigh one packed tote so the load math uses real numbers.
Shelf-opening calculator for 27-gallon totes
The table uses Sterilite’s two 27-gallon totes and these planning allowances: 1 in. at each end and between totes, 1 in. front and back, and 3 in. above the lid for lifting. The allowances are ours, not the maker’s; tighten or loosen them to suit how you lift.

| Arrangement | Larger tote (30 1/2 x 20 5/8 x 15 1/4 in.) | Standard tote (28 1/2 x 19 5/8 x 15 1/2 in.) |
|---|---|---|
| Two totes, long side out: clear width | 64 in. (2 x 30 1/2 + 3) | 60 in. (2 x 28 1/2 + 3) |
| Long side out: usable depth | 22 5/8 in. (20 5/8 + 2) | 21 5/8 in. (19 5/8 + 2) |
| Three totes, long side out: clear width | 95 1/2 in. (3 x 30 1/2 + 4) | 89 1/2 in. (3 x 28 1/2 + 4) |
| Two totes, end out: clear width | 44 1/4 in. (2 x 20 5/8 + 3) | 42 1/4 in. (2 x 19 5/8 + 3) |
| Three totes, end out: clear width | 65 7/8 in. (3 x 20 5/8 + 4) | 62 7/8 in. (3 x 19 5/8 + 4) |
| End out: usable depth | 32 1/2 in. (30 1/2 + 2) | 30 1/2 in. (28 1/2 + 2) |
| Clear height per opening | 18 1/4 in. (15 1/4 + 3) | 18 1/2 in. (15 1/2 + 3) |
Watch the width. Two of the larger totes long side out need 64 in. between the posts. The posts on a unit that measures 72 in. outside take part of that width, so measure the clear opening before you count on two totes per shelf.
For your own totes, multiply the dimension facing you by the number of totes and add your end and between gaps. Add the front and back allowance to the dimension that runs into the shelf, and the lifting allowance to the height. The clear height is the space between the deck and the shelf above it, not the spacing between mounting holes.
Example: a 72-inch unit in a one-car garage
Example: a 10 x 20 ft one-car garage with a clear back wall and a unit that measures 72 in. wide and 24 in. deep outside, with at least 64 in. between its posts, 22 5/8 in. of usable depth and four openings of 18 1/4 in.
That unit holds two of the larger totes per shelf, long side out, so eight totes on four levels. Four 18 1/4 in. openings add up to 73 in. before shelf thickness and the frame, so check the unit’s overall height against your wall and any door track. Across the garage, the 24 in. depth leaves 96 in. of the 120 in. width (120 − 24 = 96) for parking and the car doors.
For the load, say each packed tote weighs 40 lb (an example; weigh yours). Two per shelf is 80 lb per shelf and 320 lb for the unit. Compare those numbers with the shelf rating and the unit rating on the label.
Shelving types that fit 27-gallon totes
Freestanding units 24 in. deep
The simplest fit for totes long side out. Look for at least 22 5/8 in. of usable depth for the larger Sterilite tote, a deck that supports the whole tote base, and anti-tip hardware in the box. Compare 24-in.-deep garage shelving units on Amazon.
Wide units for two or three totes per shelf
Useful if you want two totes long side out (64 in. clear for the larger tote) or three end out (65 7/8 in. clear and 32 1/2 in. deep). Measure between the posts, not the overall width. See 72-in.-wide garage shelving units on Amazon.
Wall-mounted standards and brackets
Good when you want the floor clear below the totes. The brackets need to reach the tote’s full front-to-back dimension, and the standards go into studs or masonry, not drywall alone. Longer brackets usually carry less, so read the rating for the length you buy. See heavy-duty wall-mounted shelving standards and brackets on Amazon.
DIY lumber tote rack
Two-by rails screwed to uprights, spaced so the lid lip rides on the rails while the tote body hangs between them. It’s the most compact way to store totes end out, and you can slide any tote out like a drawer. Example cut list for one column of five totes, end out, built for a tote 19 5/8 in. wide at the rim:
| Part | Qty | Size | Note |
|---|---|---|---|
| Uprights | 4 | 2×4 at your chosen height | front and back, each side |
| Rails | 10 | 2×2 or ripped 2×4, tote length + 1 in. | one pair per tote |
| Cross ties (top and bottom) | 4 | 2×4, cut after you dry-fit one tote | sets the rail spacing |
| Fasteners | as needed | structural or construction screws | pre-drill near board ends |
Set the gap between rail faces just under the width of the lid lip. Hang the heaviest totes on the lowest rails, since the rim carries the whole load on this kind of rack. If you need matching totes, see heavy-duty 27-gallon storage totes with lids on Amazon; buying them in one batch keeps the footprint consistent.
Measuring mistakes that cause a poor fit
- Measuring the tote base instead of the rim. The lid and handles stick out farther than the base.
- Treating the outside size as the opening. Posts, back braces and shelf beams take up space.
- Counting levels without the shelf thickness. Add the decks and frame to the clear openings before comparing with your wall height.
- Leaving no way out. A tote needs room to slide out and be lifted, clear of the car and the door tracks.
- Letting a tote bridge a gap. On shelving, set the base fully on the deck. Rail racks are the exception, by design.
Load and anchoring
Before loading, compare the packed weight per shelf with the shelf rating and the total with the unit rating. Anchor freestanding units and wall standards the way the maker specifies, into studs or masonry, and keep the heaviest totes low.
Where tote shelving fits in a small garage
Totes hold things you reach for a few times a year, so they belong on the back wall rather than beside the bench. For the full plan, see our guide to tool storage for a small garage. Keep daily tools on a pegboard tool wall near the bench, park a rolling tool cart where it won’t block the totes, and put small parts and chemicals in wall-mounted tool cabinets. Seasonal totes can go overhead on ceiling-mounted storage racks.
FAQ
Yes, long side out. Sterilite’s two 27-gallon industrial totes are 19 5/8 and 20 5/8 in. wide, which leaves 3 3/8 to 4 3/8 in. to spare on a shelf with 24 in. of usable depth. End first, no: they’re 28 1/2 to 30 1/2 in. long, so you’d need about 30 1/2 to 32 1/2 in. of depth.
Two long side out, if the opening between the posts is at least 60 in. for the standard Sterilite tote or 64 in. for the larger one. Three fit end first if you have 62 7/8 to 65 7/8 in. between the posts and 30 1/2 to 32 1/2 in. of depth.
The totes in this guide are 15 1/4 to 15 1/2 in. tall with the lid on. Our calculator adds 3 in. for lifting, for an 18 1/4 to 18 1/2 in. clear opening. Add more if the shelf has a front lip you have to lift over.
You can, within reason: Sterilite tells buyers to use good judgment when stacking and to keep the heaviest bin at the bottom. Separate shelves cost more wall height, but they let you pull out a lower tote without unstacking the ones above it.
Weigh one packed tote with its lid, multiply by the number of totes on the shelf, and compare that with the shelf rating on the label. Then add up every shelf and compare the total with the rating for the whole unit.
How Deep Should Garage Shelves Be for Totes?
[…] is part of our guide to tool storage for a small garage. If your totes are 27 gallons, our guide to garage shelving for 27-gallon totes covers widths, shelf spacing and a DIY […]