How Deep Should Garage Shelves Be for Totes? Measure This First

A garage shelf needs to be at least as deep as the side of the tote that runs front to back, plus a little clearance. For Sterilite’s totes from 18 to 38 gallons, that makes 24 in. of usable depth enough when the totes sit long side out, because the widest one measures 21 5/8 in. An 18-in. shelf is too shallow for every tote in our table. If you want totes to slide in end first, the depth has to match the tote’s length instead: about 25 to 39 1/2 in. with clearance.

As an Amazon Associate I earn from qualifying purchases.

This is part of our guide to tool storage for a small garage. If your totes are 27 gallons, our guide to garage shelving for 27-gallon totes covers widths, shelf spacing and a DIY rack.

The rule: depth equals the tote side facing in

  • Long side out. You see the long side; the tote’s width runs into the shelf. Depth needed = tote width.
  • End out. You see the short end and slide the tote in like a drawer. Depth needed = tote length.

Then add clearance. This guide uses 1 in. at the front and 1 in. at the back, so the tote sits fully on the deck instead of on its rim at the edge.

Top-view diagram showing that tote width sets shelf depth long side out and tote length sets it end out
The same 27-gallon tote needs 19 5/8 in. of depth long side out and 28 1/2 in. end out, before clearance.

Measure your tote in 3 steps

  1. Put the lid on and measure length and width across the rim and handles. That’s the widest point, and it’s where makers measure too.
  2. Measure the height with the lid on.
  3. Pick the orientation and note the dimension that runs front to back. Add your clearance; that’s your minimum usable shelf depth.

How deep garage shelves should be, by tote size

These are Sterilite’s listed exterior sizes for five common totes, with the depth each one needs.

ToteMaker’s exterior size, L x W x H (in.)Depth long side out: tote width (with 1 in. front and back)Depth end out: tote length (with 1 in. front and back)
18-gal. Sterilite tote23 1/8 x 18 1/8 x 14 7/818 1/8 in. (about 20 1/8 in.)23 1/8 in. (about 25 1/8 in.)
20-gal. Sterilite latch tote23 5/8 x 18 1/4 x 15 1/218 1/4 in. (about 20 1/4 in.)23 5/8 in. (about 25 5/8 in.)
27-gal. Sterilite industrial, standard28 1/2 x 19 5/8 x 15 1/219 5/8 in. (about 21 5/8 in.)28 1/2 in. (about 30 1/2 in.)
27-gal. Sterilite industrial, larger30 1/2 x 20 5/8 x 15 1/420 5/8 in. (about 22 5/8 in.)30 1/2 in. (about 32 1/2 in.)
38-gal. Sterilite industrial37 1/2 x 21 5/8 x 15 7/821 5/8 in. (about 23 5/8 in.)37 1/2 in. (about 39 1/2 in.)
  • 24 in. covers every tote here long side out. The widest needs 23 5/8 in. with clearance.
  • 18 in. is too shallow for all of them. The narrowest, the 18-gallon tote, is 18 1/8 in. wide.
  • End out needs a deep or custom rack. From about 25 1/8 in. for the 18-gallon tote to 39 1/2 in. for the 38-gallon one, which usually means a lumber rack built to your tote.
  • Same capacity, different size. Sterilite’s two 27-gallon industrial totes differ by 2 in. in length and 1 in. in width, so measure the totes you own.

Worked example: one wall, mixed totes

Example: four of the larger 27-gallon totes and four 18-gallon totes on one 72-in.-wide, 24-in.-deep unit, long side out, with 1 in. at each end and between totes.

  • Two 27-gallon totes need 64 in. between the posts (2 x 30 1/2 + 3) and 22 5/8 in. of depth.
  • Three 18-gallon totes would need 73 3/8 in. (3 x 23 1/8 + 4), more than a 72-in. unit has between its posts, so plan on two per shelf: 49 1/4 in.
  • Four shelves hold all eight totes, with the heavier 27-gallon totes on the bottom two.

Shelf types for totes

  • Freestanding steel or resin units: usable depth from the table, a per-shelf weight rating above your packed totes, and anti-tip hardware. Compare 24-in.-deep garage shelving units on Amazon.
  • Wall brackets: brackets at least as long as the depth you need, rated for that length, and screwed into studs.
  • DIY or kit rail racks: built to your tote’s rim width and length; the best fit for end-out storage. See tote racks and rail kits on Amazon if you’d rather not build one.

Mistakes that come from measuring wrong

  • Measuring the tote body instead of the rim and handles.
  • Assuming every “27-gallon” or “18-gallon” tote is the same size.
  • Using a shelf’s overall width or depth instead of the usable space between posts and braces.
  • Forgetting lift room above each tote.
  • Putting the deepest shelving where the car door needs to open. Our small workshop layout ideas help you place it, and seldom-used totes can go overhead on ceiling-mounted storage racks.

How we researched this: As of November 2026, we took tote dimensions from Sterilite’s product pages and worked out the depths and counts in this guide from them. It covers sizing rules and shelf types rather than ranking specific models.

FAQ

Is an 18-inch-deep shelf deep enough for totes?

Not for the totes in this guide. Even Sterilite’s 18-gallon tote is 18 1/8 in. wide, so it overhangs an 18-in. shelf long side out, and with 1 in. of clearance front and back it needs about 20 1/8 in. of usable depth.

Are 24-inch-deep shelves good for storage totes?

Yes. Every tote in our table, from 18 to 38 gallons, fits long side out on a shelf with 24 in. of usable depth: the widest, Sterilite’s 38-gallon industrial tote, is 21 5/8 in. wide, or 23 5/8 in. with clearance.

Should totes go long side out or end out?

Long side out needs less depth and works with standard shelving. End out needs a shelf as deep as the tote is long, but it uses less wall width per tote and lets you pull each one out like a drawer.

Do I measure the tote at the top or the bottom?

At the top, with the lid on. Totes taper, and makers list the exterior size at the rim because the lid and handles stick out farthest there.

Do 38-gallon totes fit on standard garage shelves?

Long side out, yes, on a shelf with 24 in. of usable depth: Sterilite lists its 38-gallon industrial tote at 37 1/2 x 21 5/8 in. Width is the limit. One fits on a 48-in. shelf, and two side by side need about 78 in. between the posts (2 x 37 1/2 in. plus 1 in. at each end and between), more than a 72-in. unit offers.

Sources

Best Home Gear Hub Editorial

The editorial team at Best Home Gear Hub publishes practical guides to help homeowners choose and use tools, garage gear, and household equipment. Articles are researched from manufacturer specifications, publicly available product information, and established home-maintenance practice. We use AI-assisted drafting with editorial review.

Leave a comment

Your email address will not be published. Required fields are marked *